filename: TFS70BT.doc version 1.1 21.03.2012 vectron international filter specification tfs 70bt 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: * input: 106.68 || -57.85 pf output: 121.17 || -51.00 pf characteristics remark: the reference level for the relative attenuation a rel of the tfs 70bt is the minimum of the pass band at tenuation. this value is defined as the insertion l oss a e . the nominal frequency f n is fixed at 70 mhz without any tolerance. the valu es of relative attenuation a rel are guaranteed for the whole operating temperature range. the frequency shift of the filte r in the operating temperature range is included in the production tolerance scheme. d a t a typ. value tolerance / limit insertion loss a e 9.7 db max. 12 db (reference level) nominal frequency f n - 70 mhz passband pb - f n 2.5 mhz pass band ripple 0.5 db max. 1 db relative attenuation a rel f n ? f n 2.5 mhz 0.5 db max. 1 db f n 7.0 mhz ? f n 10.0 mhz 42 db min. 38 db f n 10.0 mhz ? f n 20.0 mhz 43 db min. 40 db group delay ripple within pb p-p 70.0 ns max. 125 ns phase linearity within pb p-p 4.3 deg max. 6.0 deg input/output return loss 16 db min. 10 db operating temperature range otr - - 55 c ... + 125c storage temperature range - - 55 c ... + 125c temperature coefficient of frequency tc f ** -88 ppm/k *) the terminating impedances depend on parasitics and q-values of matching elements and the board use d, and are to be understood as reference values only. should there be additional questions do not h esitate to ask for an application note or contact o ur design team. **) ? f(hz) = tc f (ppm/k) x (t-t 0 ) x f cat (mhz). generated: checked / approved:
filename: TFS70BT.doc version 1.1 21.03.2012 vectron international filter specification tfs 70bt 2/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. 50 54 58 62 66 70 74 78 82 86 90 -80 -72 -64 -56 -48 -40 -32 -24 -16 -8 0 frequency in mhz magnitude in db insertion loss: -9.70 db 65.11 66.11 67.11 68.11 69.11 70.11 71.11 72.11 73.11 74.11 75.11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 frequency in mhz magnitude in db 65.11 66.11 67.11 68.11 69.11 70.11 71.11 72.11 73.11 74.11 75.11 0.752 0.7808 0.8096 0.8384 0.8672 0.896 0.9248 0.9536 0.9824 1.0112 1.04 frequency in mhz delay in s filter characteristic construction and pin connection (all dimensions in mm) 9,3 max. 7,3 max. 2 max. 5,08 2,54 0,8 0,1 0,9 r 0 , 3 date code 1 3 50 test circuit 50 1 2 7 6 3, 4, 5, 8, 9, 10 l1 c1 50 c2 l2 tfs 70bt b30 1 input 2 input rf return 3 ground 4 ground 5 ground 6 output 7 output rf return 8 ground 9 ground 10 ground date code: year + week b 2011 c 2012 d 2013 ...
filename: TFS70BT.doc version 1.1 21.03.2012 vectron international filter specification tfs 70bt 3/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 p lanes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 2000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direc tion pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w :16,00 0,3 po :4,00 0,1 do :1,50 +0,1/-0 e :1,75 0,10 f :7,50 0,10 g(min) :0,60 p2 :2,00 0,1 p1 :12,00 0,1 d1(min) :1,50 +0,1/-0 ao :7,60 0,10 bo :9,60 0,10 ct :13,5 reel (all dimensions in mm) a : 330 w1 :16,4 w2(max) :22,4 n(min) : 50 c :13,0
filename: TFS70BT.doc version 1.1 21.03.2012 vectron international filter specification tfs 70bt 4/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS70BT.doc version 1.1 21.03.2012 vectron international filter specification tfs 70bt 5/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh & co. kg reserves the ri ght to make changes to the product(s) and/or inform ation contained herein without notice. no liability is assumed as a result of the ir use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 - generation of development specification tcuk 11.10.2011 1.1 - add typical values, change development to fil ter specification tcuk 21.03.2012
|
